I made these 12 cards from a 12" X 12" One Sheet Wonder that I stamped using Painted Harvest Stamp Set. It's sometimes fun to make your own Designer Series Paper (DSP). I used Blushing Bride, Sweet Sugarplum, Crumb Cake and Soft Suede Ink Pads for the sunflowers and Pear Pizzazz Ink Pad (stamped off once) for the leaves and then Sweet Sugarplum Ink Pad for the little dots to fill in around the card stock. There are 2 videos to watch. First is how i made the One Sheet Wonder Design and the 2nd one is cards I made using it.
How to make your own design using Painted Harvest
Then I cut it as template shows.
I did cut some of the pieces smaller or used them for sentiments etc.
All edges are sponged with Sweet Sugarplum Ink and all sentiments are stamped in the same Sweet Sugarplum. All cards are sprayed with a homemade glimmer Spray (Watch video if you want to make some)
Video Tutorial
Cards 1-4
1. Upper Left- Embossed with layered leaves folder, I used a 2" x 5 /14" DSP with a blushing bride backing. I cut out an oval , stamped sentiment on the back and then die cut a larger oval scallop then cut another oval inside of that to make the frame. Popped up the DSP on dimensionals. Added silver bakers twine and a bow.
2. Upper Right- Embossed with layered leaves folder, I used a 2 1/2" x 4" DSP with a blushing bride backing. Popped DSP on dimensionals. Stamped the sentiment and punched out using the classic label punch, applied with glue dots to the silver bakers twine and bow.
3. Lower Left- Embossed with layered leaves folder. Use corner rounder or envelope punch board to round all corners on DSP and Backing. I used a 2 1/2" x 4" DSP with a blushing bride backing. Die cut circle and frame (same as card #1). Wrapped silver bakers twine 3 times and added a bow. Popped DSP up on dimensionals.
4. Lower right-I used the sponge brayer with sweet sugarplum ink for an ombre effect. Die cut scalloped square in blushing bride, square in sweet sugarplum and DSP in stitched square and placed on an angle with adhesive. Then added 3 small pearls under the sentiment.
Cards 5-8
5. Upper Left- (Watch video for this one).
6. Upper Right- Gate fold card (8 1/2 X 5 1/2" card stock, scored at 2 1/8" on both ends). Inside is blushing bride card stock. Embossed both front openings with flowered petal pair folder. Layered DSP on blushing bride and placed on left side (with the adhesive only the left side) , Stamped and cut out sentiment with punch and added a couple of pearls.
7. Lower Left- Fold back 1 1/4" of cardfront, emboss with layered leaves folder. Sponge brayer the left portion of the card with sweet sugarplum ink. Cut your DSP into a square add backing, punch 1/8" hole on top and bottom of (Square angled like a triangle) triangle. Thread silver bakers twine and glue to back of embossed 1 1/4" add a bow. Adhere layered leaves embossed part down. Stamp sentiment on inside of card.
8. Lower Right- Emboss with flowered petal pair folder at top and bottom of card. Cut rectangle frame from in blushing bride (use square die, run through once, move to second position and line up with first cut add a bit of washi tape to hold die in place, run through big shot again) add a bow of silver bakers twine, add 3 pearls above sentiment.
Cards 9-12
9. Upper Left- Emboss with layered leaves embossing folder. Use a sponge brayer with sweet sugarplum ink on leaves. Cut oval and framed oval cut out (like card #1). Stamp sentiment and glue in place on blushing bride card stock. Add silver bakers twine 3 times around DSP and add your bow. Pop up on dimensionals and place on card
10. Upper Right- Emboss both left and right of card front with flowered petal pair. Sponge with sweet sugarplum with brayer. Cut 1 1/2" X 4" DSP and glue in center. Using washi tape mask your stamp to get the 3 separate parts of the sentiment. Add backing and adhere to card.
11. Lower Left- Similar to card #3 except only round two of the corners.
12. Lower Right- emboss with layered leaves folder. Punch out space for sentiment on DSP using classic label punch. Glue sentiment in place on blushing bride card stock, wrap silver bakers twine twice on an angle on DSP add dimensionals and place on backing so you can see the sentiment below.
You can use any stamp set and design your own DSP, it's fun, give it a try. Use what you have available, if you don't have this stamp set or embossing folders or punches substitute with what you do have. That is unless i've shown you something you just gotta have :) you can purchase by clicking the links below or visiting my website and clicking on SHOP NOW to visit my Stampin" Up Store.
(www.astampingnana.com)
If you have any questions feel free to contact me by clicking the contact me button on my website too.
No comments:
Post a Comment
Note: Only a member of this blog may post a comment.